Blue container lifted by a crane at dusk

Project cargo · Machinery · Out of gauge

Project cargo and machinery, planned end to end

Excavators, generators, plant and anything else that does not fit in a box. We survey the move, choose the equipment and the route, arrange the permits and escorts, and supervise loading and lashing at both ends, under our own house bill of lading.

  • Flat rack and open top
  • Breakbulk and RoRo
  • Heavy haul and permits
  • Supervised lashing
Direction
Shipping mode

Step 1 of 5 · about 2 minutes

The right equipment

Matched to the cargo, not the other way round

Every project starts with the dimensions and the weight. From there we specify the equipment that carries the piece safely at the best cost.

  • Open top

    For cargo too tall for a standard container or loaded by crane from above, sealed with a tarpaulin.

  • Flat rack

    No roof and no side walls, for machinery wider or taller than any container.

  • Breakbulk

    Units too large for a flat rack, loaded piece by piece into the vessel.

  • RoRo

    Wheeled and tracked machinery driven on and off the ship.

How a project moves

One plan from the factory floor to the site

The same team owns every stage, so the survey, the trucking, the booking and the paperwork all describe the same cargo.

  1. Step 1

    Survey

    Dimensions, weights, lifting points and photos of every piece, checked against the equipment and the route.

  2. Step 2

    Plan

    Equipment, vessel, port and route chosen, with the oversize permits and escorts arranged.

  3. Step 3

    Pickup

    Flatbed, lowboy or heavy haul from your facility to the port.

  4. Step 4

    Loading and lashing

    Lifting, loading and securing supervised, so the cargo sails as it was planned.

  5. Step 5

    Documents

    Our own house bill of lading, the AES export filing and the papers the destination asks for.

  6. Step 6

    Destination

    Discharge, clearance and delivery to site through our partners abroad.

Container guide

Which container fits your cargo?

Pick a container to see its inside measurements and what it suits best. Not sure? Send us the cargo details and we'll choose for you.

Quote a 40' HC

Typical figures. Exact measurements and payload vary by carrier and box.

ISO 668 · 40' High CubeExternal dims · mm
Backhoe loader chained down on a lowboy trailer, ready for transport to port
Heavy haulPickup to the port on the right trailer

US trucking

The road leg, planned with the sea leg

Oversized cargo is often hardest to move before it reaches the port. We book the flatbed, lowboy or heavy haul truck, arrange the state permits and escorts, and survey the route where the load calls for it.

The trucking is timed to the vessel, so the cargo reaches the terminal inside its receiving window and does not wait on the pier.

  • Flatbed, lowboy and heavy haul
  • Oversize permits and escorts
  • Route surveys for the largest loads

Where it goes

Machinery to the lanes we know best

Questions

Project cargo questions

Short answers to what shippers ask us about oversized and heavy cargo.

What counts as project cargo?
Anything that needs its own plan to move: machinery and plant, generators, vehicles and equipment that are too heavy, too tall or too wide for a standard container, and shipments made up of many pieces that must arrive together for one site. We survey it, choose the equipment and the route, and supervise the loading.
Flat rack or open top: which does my cargo need?
An open top suits cargo that is too tall for a standard container or has to be lowered in by crane: it is covered with a tarpaulin instead of a roof. A flat rack has no roof and no side walls, so it takes cargo that is wider or taller than any box. Units too large even for a flat rack go breakbulk, and wheeled or tracked machinery can go RoRo. Send us the dimensions and weights and we will specify the equipment.
What do you need from me to price a project move?
Length, width, height and weight of each piece, the lifting points and centre of gravity if they are marked, photos or drawings, the pickup and delivery addresses, and the date the cargo is ready. With those we come back with the equipment, the route, the permits and a price.
Do you arrange the oversized trucking in the US?
Yes. We book flatbed, lowboy and heavy haul trucking to the port, arrange the oversize permits and escorts the route needs, and survey the route where the load calls for it.
Can machinery parts go by air?
Yes. Spare parts and machinery components fly when a vessel would take too long, for example to keep a site in Asia or the Gulf running. We price the same shipment by sea and by air so you can see the trade-off.
Can you still ship heavy cargo to the Gulf with the Strait of Hormuz restricted?
Yes. Gulf-bound cargo routes through Khor Fakkan, Fujairah, Sohar or Jeddah with onward trucking. We confirm the gateway, the onward leg and the transit time before you commit.
Is there anything special about machinery to Australia?
Yes. Australia requires machinery to arrive clean, free of soil and seeds, and from September to April machinery, vehicles and steel from the US also need stink bug treatment before they sail. Plan the cleaning and treatment into the schedule. See our Australia page.

Still have a question? Call (908) 440-0999 or email [email protected].

Get a quote

Moving machinery? Send us the dimensions.

Send the length, width, height and weight of each piece, with the pickup and delivery points. We come back with the equipment, the route and the price.

  • Ocean, air, trucking and vehicles
  • No obligation, no sign-up
  • Cargo released within 60 minutes of payment
Start your quote